MROSupply Has Hundreds Of Brands, Millions Of Products, Including
Image for Illustration purposes only. Actual product may vary
$3,306.19 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Free Gift with this product
Typically Ships in: 1 day
Returnable: See conditions
Base to center height
6.3100 in, 160.274 mm
Bearing component
Mounted Bearing
Bearing type
Spherical roller, spherical roller
Bolt Diameter
1.0000 in
Bolt to bolt max
18.2500 in, 463.55 mm
Bolt to bolt min
16.7500 in, 425.45 mm
Bolt width
3.7500 in, 95.25 mm
Bore length
9.2800 in, 235.712 mm
Expansion capability
Non-expansion (fixed)
Greasable
Yes
Housing construction
Split
Housing type
Four-bolt pillow block
Insert material
Steel
Lubrication type
Grease
Max Speed
1400 RPM
Sensor ready
Yes
Shaft attachment
Tapered adapter
Shaft diameter
4.1875 in
Static load capacity
265000 lbf, 1178778.728 N
DODGE UNIFIED SAF and SDAF Pillow Blocks
Features/Benefits
- Cast iron, closed-end housings offer greater protection in high pressure washdown environments. Available from stock.
- Solid cast iron feet increase strength in both two and fourbolt styles.
- Large capacity oil sump lowers operating temperatures, undercut bearing seat allows full lateral travel of expansion bearing, prevents stabilizer ring from binding, makes installation easy
- Oil return slots are cast into the interior seal grooves to keep lubricants in. This allows oil in the seal grooves to return to the oil sump instead of leaking.
- Standard modifications for wet and harsh environments include nylon coating, epoxy paints and nickel plating, as well as stainless steel hardware.
- New drop-in TRIPLE-TECT Seal makes seal installation easier
- Exclusive oil-equalization passage simplifies maintenance. Pillow block can be drained completely from either side.
- Offset dowels with matched numbers on cap and base joint simplify correct assembly.
SKU: 126843
Replacement pillow block bearing
I ordered 2 Dodge Pillow block bearings to replace replace a failed bearing on my chipper and to replace a second bearing as a precaution. I received the both bearings promptly, but discovered that the failed bearing also damaged it's housing. Since the housing without a bearing doesn't seem to be readily available, I requested to return the one bearing and replace it with the complete pillow (housing with bearing). Since I was getting an entirely different part, MROSupply customer support suggested that I get a full refund for the bearing and place a new order for the pillow block (housing with bearing). I have received the pillow block and am waiting for the refund which I expect to receive very soon.
Read more
Face Runout/OD is the variation of the outside surface generatrix inclination with the face. This tolerance is meant to help ensure the outer ring of the bearing is close enough to a right angle with the face of the outer ring. The figures for the face runout/OD are provided for P4 and P5 grades. Note that all points on a single circle of the outside ring bore adjacent to the face are calculated based on one revolution. However, the inner ring must remain stationary. Then, the bearing is turned over and the outer side of the ring measured. Finally, the largest measurement is taken away from the smallest to get runout/OD bore tolerance.
Read MoreWhen you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
SKU: 126843
Replacement pillow block bearing
I ordered 2 Dodge Pillow block bearings to replace replace a failed bearing on my chipper and to replace a second bearing as a precaution. I received the both bearings promptly, but discovered that the failed bearing also damaged it's housing. Since the housing without a bearing doesn't seem to be readily available, I requested to return the one bearing and replace it with the complete pillow (housing with bearing). Since I was getting an entirely different part, MROSupply customer support suggested that I get a full refund for the bearing and place a new order for the pillow block (housing with bearing). I have received the pillow block and am waiting for the refund which I expect to receive very soon.
Read moreItem must be unused and undamaged, in it's orginal package. For Dodge there is typically a 10% + $30 US re-stocking fee, although it may vary from case to case. Re-packing fees may apply. Re-stocking fee applies bor both returns for credit and return for exchange.
Warranty is redeemed directly with manufacturer. If your item was damaged during usage, please let us know and we will help you get in touch with your nearest service center, they will guide you about the steps to follow to redeem the manufacturer's warranty.
For further information on our returns/warranty policy, please visit:
https://www.mrosupply.com/page/returnwarranty-policy/