MROSupply Has Hundreds Of Brands, Millions Of Products, Including
Image for Illustration purposes only. Actual product may vary
Dixon
B30 Boss® Clamp 4 Bolt Type, 2 Gripping Fingers
MODEL B30
Contact supplier for technical support on: 8779634966
$52.22 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Orders over $500 qualify for a Free Gift
Typically Ships in: 1 day
Returnable: See conditions
California Prop 65 warningHose I.D. (in)
2 (50 mm)
Hose OD From
3-6/64 in (78.6 mm)
Hose OD To
3-28/64 in (87.3 mm)
Material
Zinc plated iron
Torque
60 ft. lbs.
Features
4-bolt type clamp with 2 gripping fingers and 2 clamp sections
Instructions
- 4 Bolt Dixon Boss Clamp Bolt Tightening Sequence, Using a torque wrench, begin tightening the bolts as follows:
- A) Back bolt (bolt with nut facing assembler that is furthest away from gripping finger) 1 full turn.
- B) Front bolt (bolt with nut facing assembler that is closest to gripping finger) 1 full turn.
- C) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
- D) Opposite side back bolt (bolt with nut facing assembler furthest away from gripping finger) 1 full turn.
- E) Opposite side front bolt (bolt with nut facing assembler closest to gripping finger) 1 full turn.
- F) Snug by hand (if bolts are loose) nuts on opposite side of bolts just torqued.
- G) Repeat above procedure "a" through "f" until all of the bolts have reached the recommended torque.
- H) Remove assembly from vise.
Safety Notes
- The bolts used in the Boss interlocking clamps are not standard bolts. They vary from standard bolts in their length, diameter, overall thread length and material hardness. These bolts can be retorqued, but it is not recommended that the bolts or clamps be reused, as they are designed for a single bend only. Dixon Recommends using only factory supplied replacement bolts. Replacement nuts and bolts are available, contact Dixon for more information.
- Torque values for clamps are based on dry bolts. The use of lubricant on bolts will adversely effect clamp performance. Do not lubricate nuts and bolts. Recommended torque rating in ft. lbs.
- Worn-out hose couplings can be dangerous. They should be checked regularly and replace when necessary. Each coupling user should review applications and add safety devices where indicated.
- Note. Pressurized steam is an extremely dangerous commodity. Only hose, fittings, clamps and accessory items that have been approved for steam service should ever be used! Never use an unapproved item for steam service. Always follow the manufacturer's product recommendations for pressurized steam handling.
Specifications
Recommended for steam service up to 450°F (232°C).
Use
- Bolts in Boss Clamps are designed to bend as they are tightened. This allows the clamp to conform to the hose outside diameter.
- Always tighten bolts to their specified torque value.
- Periodic re-tightening of bolts is required due to "cold flow" phenomenon present in all rubber hoses.
- Boss Clamps are for single use only! Once removed they are to be discarded.
When you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
