![GAS3885TO](https://static.mrosupply.com/cache/0a/60/0a609aae64396ca3937d1d2d3c4e3ca3.jpg)
Image for Illustration purposes only. Actual product may vary
Dixon
GAS3885TO Holedall® Light Duty Stainless Ferrule
Dixon GAS3885TO Holedall® Light Duty Stainless FerruleMODEL GAS3885TO
Contact supplier for technical support on: 8779634966
$55.51 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Orders over $500 qualify for a Free Gift
Typically Ships in: 1 day
Returnable: See conditions
California Prop 65 warningHose I.D. (in)
3 (75 mm)
Hose OD From
3-47/64 in (94.9 mm)
Hose OD To
3-54/64 in (97.6 mm)
Material
304 stainless steel
Applications
Recommended for use where lower working pressures are encountered, on most one and two wire braid reinforced hoses, fiber reinforced (braided or spiraled) with or without helical wire such as: oil and suction discharge hose, barge and dock loading and unloading hose as well as L.P. gas hose, anhydrous ammonia hose, acid chemical hose and air and water hose.
Note
- Consult Dixon for die recommendations.
- Consult maximum working pressure chart or consult Dixon for specific pressure recommendations.
Safety Notes
- Dixon Holedall stems and ferrules are specifically designed to be used together as a coupling system.
- Due to differences in dimensions and tolerances, for safety reasons, do not use other manufacturer's stems or ferrules with Dixon Holedall products.
- The selection of ferrules is very important to achieve the proper coupling-to-hose assembly.
- Do not use a wrench or vice on ferrule
- Holedall couplings, regardless of coupling style, are never to be used for steam service at any pressure.
- Holedall fittings are not to be used with cable reinforced high-pressure hose, 4 or 6 braid wire hydraulic hose or any other service not listed in the recommendations. Consult Dixon for recommendations on usage.
- Externally swaged Holedall couplings, to perform satisfactorily, must be applied properly in accordance with Dixon's assembly procedures, using correct die and ferrule for that particular hose end OD. Dixon's Die and Ferrule Recommendation Guide is to be used to select correct dies and ferrules. Consult Dixon if you do not have an updated Die and Ferrule Recommendation Guide.
- Hose service working pressure (including surges and spikes) is never to exceed the maximum recommended working pressure for the fitting. The assembly's (hose + coupling) maximum working pressure is the lesser of the hose rated working pressure or the coupling rated working pressure.
- Media being transported through the hose should be compatible with the stem material. Compatibility of ferrule material with the environment in which it will be used is recommended. Consult the Compatibility Chart or the Dixon factory for material compatibility.
- For applications other than the ones list, please consult Dixon.
Use
Light duty 304 stainless ferrules for use with standard length stems such as the TMR series.
When you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
![](https://documents.mrosupply.com/file_uploads/freegifts_1.png)
Brand | PTI |
Model | 12B-15HTL-1610 |
Brand | SKF Bearing |
Model | FNL 513 A |
Brand | Flexco |
Model | 02751 |
Brand | SKF Bearing |
Model | SNL 3040 |