MROSupply Has Hundreds Of Brands, Millions Of Products, Including
Image for Illustration purposes only. Actual product may vary
SPX ATOPA55A-00012 PA55A-B-A-A-A-A-A-B-D-BB-A-G
MODEL SPX ATOPA55A-00012
Contact supplier for technical support on: 800-477-8326
$5,542.33 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Free Gift with this product
Typically Ships in: 1 day
Returnable:No
Order a "Custom Built" Hydraulic Pump
“Assemble to Order” means you can choose a basic pump with gas, air or electric motor. Then select the proper valve, gauge, pressure control, motor control and reservoir. You get a two-stage pump that gives high oil volume for fast cylinder approach (and return with double-acting cylinders) in the first stage and high pressure in the second stage.
1-1/8 HP Universal Motor. These motors start under full load and are suitable for operation up to 5, 000 or 10, 000 psi. The motor is 1-1/8 hp, 12, 000 rpm, 115 or 230VAC (specify), 50/60 cycle AC single-phase (25 amp draw at 115VAC). With proper valve they can be used with single or double-acting cylinders. NOTE: Remote control available.
1-1/2 HP Jet Motor, Single & Three-Phase. Feature low noise level, moderate speed for long service and are ideal for fixed applications. Motor is 1-1/2 hp, 3, 450 rpm, 115 or 230VAC, 50 or 60 cycle (specify), AC single-phase with thermal overload switch. Can be used with single or double-acting cylinders and equipped with remote control. Also available in 230/460VAC, three-phase (specify). NOTE: These do not start under full load unless valve is in “neutral” (requires open or tandem center valve) and are not recommended for frequent starting and stopping.
3 HP Jet Motor, Three-Phase. Gives low noise level and long life due to its moderate operating speed. Ideal for fixed installations. Consists of basic 10, 000 psi pump, jet pump motor: 3 hp, 3, 450 rpm, 230/460VAC, 60 or 50 cycle (specify). AC three-phase, with thermal overload switch. Equipped with internal and external relief valve. Will start under load.
3 HP Air Motor. This pump is ideal for use where electricity is unavailable
or cannot be used. The 5, 000 or 10, 000 psi pump has a 3 hp air-driven motor at 3, 000 rpm (optimum performance based on 80 psi air pressure and 50 cfm at the pump). You can drive single or double-acting cylinders with the correct valve. NOTE: 80 psi air supply required to start under full load.
Gasoline Engine. This version is perfect when electricity and air are
unavailable. It is capable of continuous operation at full pressure. Consists of basic 10, 000 psi pump, 4-cycle Briggs & Stratton “Diamond Edge” gasoline engine, developing 6 hp. As with all these pumps, this unit can be valved for use with either single or double-acting cylinders.
SKU: 1966869
Mro product supply
Thanks MROSUPPLY, fair prices and good stock, fast shipping and communication. Always the first stop for tooling and supplies.
Read moreWhen you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
| Brand | Cleveland |
| Model | C15931 |
SKU: 1966869
Mro product supply
Thanks MROSUPPLY, fair prices and good stock, fast shipping and communication. Always the first stop for tooling and supplies.
Read moreDisclaimer: The return policy information shown below is merely a copy of the text as stated in IDC-USA's Annual Return Policy.
File: http://documents.mrosupply.com/file_uploads/IDCreturnpolicy.pdf
ANNUAL RETURN POLICY PURPOSE: The purpose of IDC-USA’s Annual Return Policy is to allow IDC Distributors the opportunity to return salable stock merchandise of current design that may not have adequate “turns” and replace it with faster moving product.
ACCEPTANCE: IDC Owner-Distributors shall submit a return list to IDC-USA with all pertinent information as follows:
a. Product brand name
b. Quantity
c. IDC-USA’s product identification number
d. Corresponding distributor’s P.O. number or invoice number Acceptance of return shall be subject to IDC-USA inventory levels and manufacturer’s restrictions.
AUTHORIZATION: The return shall be audited and the IDC Owner-Distributor will receive an approved return list with a Return Material Authorization (RMA) number assigned to it. RETURN DATE: Each owner-distributor shall be assigned a month during which they shall be entitled to make a single annual return.
Product Qualification: All products returned must be:
a. On the current price list
b. In good resale condition
c. In the original packaging
d. Purchased from IDC-USA within 3 years of the return
e. Stock items only; no special order items
f. Only those items which have been approved
VALUE: The IDC Owner-Distributor shall receive a credit not to exceed 5% of the owner-distributor’s prior year annual purchases from the IDC Distribution Center. Credit received shall be the actual purchase price or price in effect at the time of the return, whichever is lowest, less applicable restocking charges. Additionally, all annual returns must have a minimum return value of $100.
RESTOCKING CHARGES: There will be a 15% restocking fee unless return is offset by a noncancelable order of equal value to be placed at the time of return. All items received that are not in their original box shall be subject to an additional 15% repackaging fee.
FREIGHT: Returns will be made freight prepaid by the IDC Owner-Distributor to the IDC Distribution Center. The packing slip and all cartons must reference the RMA number. The owner-distributor will be notified of any items received that do not qualify as set forth above. Those items will not be credited and shall be scrapped unless the IDC Owner-Distributor directs otherwise and assumes any additional transportation charges.