MROSupply Has Hundreds Of Brands, Millions Of Products, Including
Image for Illustration purposes only. Actual product may vary
SPX 100178 PUMP-ELE/HYD. 1/2 HP-115VAC
MODEL SPX 100178
Contact supplier for technical support on: 800-477-8326
$2,851.49 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Free Gift with this product
Typically Ships in: 1 day
Returnable:No
Input Voltage (vac)
115
Power Dissipation (hp)
0.5
Rated Speed (rpm)
3450
All of Hytec's electric/hydraulic pumps are two-stage, continuous pressure (demand) pumps that contain all the necessary controls and circuitry for powering any single- or double-acting, continuous pressure workholding system. They contain a pressure switch and pressure regulator, and each is infinitely adjustable throughout the operating pressure range of 1,000 to 5,000 psi. An internal safety relief valve prevents possible damage from exceeding the maximum rated pressure.
The first stage provides high flow at low pressure to rapidly extend clamps and cylinders. The second stage piston pump builds and maintains pressure in the system at a preset level.
The pumps' electrical controls include a RUN/JOG switch. When the pump is started in the RUN mode, it automatically starts and runs any time the pressure switch indicates the need for oil. When pressure builds to the switch setting, the pump stops until the next demand for oil lowers the pressure, causing the switch to start the pump again. The pump continues to cycle in this manner without operator intervention.
In the JOG mode, useful for set up and special applications, the pump will run only when the operator activates and holds the start switch. When released, the pump will stop immediately. If the pump builds pressure to the pressure switch setting, it will also stop. The pump cannot be forced to run after the pressure switch setting has been reached in either the RUN or the JOG mode.
Pumps having thermal overload protection have an integral "electrical shut-down" circuit which prevents the pump from restarting without manual intervention after either thermal overload or electrical service interruption. Motor electrical specifications are listed for each pump. For voltages and frequencies not listed, contact Hytec for more information.
SKU: 1966869
Mro product supply
Thanks MROSUPPLY, fair prices and good stock, fast shipping and communication. Always the first stop for tooling and supplies.
Read more
#1981279
Brand
SPX Power Team
Model
SPX 100200
#1981273
Brand
SPX Power Team
Model
SPX 100179
#1981307
Brand
SPX Power Team
Model
SPX 100280
#1981275
Brand
SPX Power Team
Model
SPX 100186
#1975217
Brand
SPX Power Team
Model
SPX 3-6105
When you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
SKU: 1966869
Mro product supply
Thanks MROSUPPLY, fair prices and good stock, fast shipping and communication. Always the first stop for tooling and supplies.
Read moreDisclaimer: The return policy information shown below is merely a copy of the text as stated in IDC-USA's Annual Return Policy.
File: http://documents.mrosupply.com/file_uploads/IDCreturnpolicy.pdf
ANNUAL RETURN POLICY PURPOSE: The purpose of IDC-USA’s Annual Return Policy is to allow IDC Distributors the opportunity to return salable stock merchandise of current design that may not have adequate “turns” and replace it with faster moving product.
ACCEPTANCE: IDC Owner-Distributors shall submit a return list to IDC-USA with all pertinent information as follows:
a. Product brand name
b. Quantity
c. IDC-USA’s product identification number
d. Corresponding distributor’s P.O. number or invoice number Acceptance of return shall be subject to IDC-USA inventory levels and manufacturer’s restrictions.
AUTHORIZATION: The return shall be audited and the IDC Owner-Distributor will receive an approved return list with a Return Material Authorization (RMA) number assigned to it. RETURN DATE: Each owner-distributor shall be assigned a month during which they shall be entitled to make a single annual return.
Product Qualification: All products returned must be:
a. On the current price list
b. In good resale condition
c. In the original packaging
d. Purchased from IDC-USA within 3 years of the return
e. Stock items only; no special order items
f. Only those items which have been approved
VALUE: The IDC Owner-Distributor shall receive a credit not to exceed 5% of the owner-distributor’s prior year annual purchases from the IDC Distribution Center. Credit received shall be the actual purchase price or price in effect at the time of the return, whichever is lowest, less applicable restocking charges. Additionally, all annual returns must have a minimum return value of $100.
RESTOCKING CHARGES: There will be a 15% restocking fee unless return is offset by a noncancelable order of equal value to be placed at the time of return. All items received that are not in their original box shall be subject to an additional 15% repackaging fee.
FREIGHT: Returns will be made freight prepaid by the IDC Owner-Distributor to the IDC Distribution Center. The packing slip and all cartons must reference the RMA number. The owner-distributor will be notified of any items received that do not qualify as set forth above. Those items will not be credited and shall be scrapped unless the IDC Owner-Distributor directs otherwise and assumes any additional transportation charges.