Image for Illustration purposes only. Actual product may vary
Dixon
2DM2-B D-Series Pneumatic Automatic Male Threaded Coupler
Dixon 2DM2-B D-Series Pneumatic Automatic Male Threaded CouplerMODEL 2DM2-B
Contact supplier for technical support on: 8779634966
$13.73 Each
Prices are subject to change
FREE SHIPPING ON ORDERS OVER $1
Select Quantity
Orders over $500 qualify for a Free Gift
Typically Ships in: 1 day
Returnable: See conditions
California Prop 65 warningBody Size
1/4 in
Hex
11/16 in
Length
2.34 in (59.4 mm)
Material
Brass
Max OD
0.98 in (24.9 mm)
Pressure Rating
See Product Details
Temperature range
-40F to 250F (-40C to 121C)
Thread
NPTF
Compatibility & Interchange Data
- Foster 3, 4, 5 and 6 Series
- Parker 30 - Series Automatic Interchange
- Hansen 3000, 4000, 5000 and 6000
Construction
- Machined components are manufactured using solid bar stock.
- Stainless steel balls, retaining rings and springs maximize corrosion resistance and extend service life.
- Nitrile (Nitrile Rubber) seals are standard
- Steel componentry is plated using ROHS Compliant Trivalent Chrome.
- Steel tubular valve
How It Works
- To disconnect, begin by holding the hose on the nipple side with three of your fingers, leaving your thumb and index finger free.
- Grab the sleeve with your thumb and index finger and begin to pull the sleeve towards the palm of your hand.
- After pulling the sleeve, the nipple will move out of the coupler slightly. Continue to hold the hose and coupler sleeve until all air is fully exhausted.
- After the line is fully exhausted, you are able to safely separate the nipple from the coupler.
Safety Notes
It is important to be safe when installing quick disconnect couplings into a pneumatic circuit. Never install a pneumatic coupling directly into an air tool, use a piece of hose that is at least 18" long, between the tool and the coupling, to prevent damage to the coupling. To protect the operator, safety devices, such as a safety check valve and safety cable should be installed in case there is a hose or coupling failure.
Specifications
- Rated pressure for connected Brass Coupler & Brass Plug: 300 PSI (20 bar) Maximum Working and 16,000 PSI (1,100 bar) Burst
- Rated pressure for connected Brass Coupler & Steel Plug: 500 PSI (35 bar) Maximum Working and 16,000 PSI (1,100 bar) Burst
SKU: 115099
Reasonable and reasonably fast shipping
My order was processed very quickly even with the changes I made on my original order with friendly people at MRO
Read moreSKU: 107691
Solid valve!
I use these valves as the trigger for some flame effects. They snap back quickly and don't wear out or pass center and leak like cheaper versions. Best bang for your buck!
Read moreWhen you get to checkout, you’ll be able to select a free gift! Depending on the cart value, you’ll be shown relevant gifts your order qualifies for.
$500
MRO Hat
MRO Golf Balls
MRO Hi-Vis Vests
MRO Mug
$750
32oz Water Bottle
Throw Blanket
30 piece Hex Set
Telescopic Pick Up
$1,250
Golf Cooler
11-in-1 Screw Driver Set
Gorilla Grip Knee Pad
John Deere Oilskin Hat
$2,500
Igloo 1/2 Gallon Jug
Rechargable Headlamp
Larix Trucker Hat
$5,000
Igloo 10 Gallon Cooler
Igloo Party Bucket Cooler
Klein Tools Speaker
Klein Tools 8-in-1
$7,500
GX-6F Pro Golf Range Finder
Bushnell Outdoorsman Speaker
Jaeger 24px Ratcheting Wrench Set
Aspen Beverage Bucket
Brand | Dixon |
Model | IH300 |
SKU: 115099
Reasonable and reasonably fast shipping
My order was processed very quickly even with the changes I made on my original order with friendly people at MRO
Read moreSKU: 107691
Solid valve!
I use these valves as the trigger for some flame effects. They snap back quickly and don't wear out or pass center and leak like cheaper versions. Best bang for your buck!
Read more