UFH50R CPLG 1/2 1/8X1/16KW

MODEL 68514413855

BRAND

LoveJoy

SKU

1796247

WEIGHT

0.500 lb

UOM

each

$294.74 Each

Prices are subject to change

FREE SHIPPING ON ORDERS OVER $1

Select Quantity

GET A QUOTE

Orders over $500 qualify for a Free Gift

Typically Ships in: 1 day

Returnable: See conditions

UFH Type - Flange-to-Shaft

A flange-to-shaft configuration, this couples flange mounted equipment to a shaft with all the benefits of Uniflex versatility. The stock flange plate is the same as used on the UF Type. The one-piece UFH Type coupling is similar to the U Type, except that one hub is replaced by a flange plate. Stock flange sizes are shown in the Dimensional Data table below but other sizes can be made to order. As with the other Uniflex styles, this coupling compensates for high degrees of angular and parallel misalignment with very little backlash or windup and is reliable in harsh or severe environments. Regular and short versions are available for each size to accommodate different overall length requirements. For increased versatility, the hub can be modified with a tapered, spline, hex or square bore. The standard hub is furnished with either a pre-drilled pin hole or with a keyway and set screw. Specify when ordering.

Note: The UFH Type coupling does not come with assembly hardware. Assembly hardware must be purchased separately.

Specifications

Description	UFH50R CPLG 1/2 1/8X1/16KW
Hub Style	Regular
Type	Flange-to-Shaft
Material	Steel
Weight	0.50 lb
Color	Gray/Metallic
Bore Type	Finished Bore
# of Mounting Screws Required	3

Dimensional Data

Bore Size	1/2 in
Hub Size	UFH50R
Set Screw Thread Size (Dimension T)	1/4-20
Keyway Size (W x D)	1/8 x 1/16 in
Dimension HD	1.040 in26.42 mm
Overall Length	2.030 in51.56 mm
Pin Location (Dimension SL)	0.310 in
Length thru Bore	0.640 in16.26 mm
Min. Bore (Dimensions ID1/ID2)	0.313 in7.95 mm
Max. Bore (Dimensions ID1/ID2)	0.500 in13.00 mm
Dimension BC	1.500 in38.10 mm
Dimension D	1.880 in47.75 mm
Flange Diameter (Dimension FD)	2.000 in50.80 mm
Dimension FL	0.250 in6.35 mm
Mounting Screw Thread Size	1/4-20
Cubic inches	8.12000 in³

Performance Data

Operating Temperature Range	-40 to 250 ºF
Max. Torque	82 in·lb
Max. Speed	30000.00 rpm
Max. Recommended End Play	0.035 in0.89 mm
Max. Parallel Offset	0.021 in0.53 mm
Wind-Up Angle at Nominal Torque	1.82 º
Wind-Up Angle at Max. Torque	4.5 º
Rated HP at 100 rpm	0.13 hp
# of Set Screws Required	1

Coupling Design

The Uniflex Coupling is an all steel, single piece coupling that solves a variety of application concerns including: high misalignment, space limitations, high temperature, and exceptionally low backlash/windup. The unique flexing center of the Uniflex consists of three opposingly wound square wire springs for forward or reverse operation. Two steel hubs are then brazed to the steel spring pack to create a durable one-piece flexible coupling.

Notes

Total backlash is approximately 1/3 of windup at maximum torque – consult Lovejoy Engineering for more information.
OAL & Dimension FL Tolerance +. 12 inch.
Mounting screws not supplied.